RENODLADGB
Consumption valuesProgramme 1)Water(l)Energy(kWh)Duration(min)P1 7 - 14 0.6 - 1.6 40 - 170P2 12.5 - 14.5 1.4 - 1.7 170 - 190P3 10 0.9 41P4 10.5 0.83 2
OptionsDesired options must beactivated every time before youstart a programme.It is not possible to activate ordeactivate options while aprogramme is
As the appliance stores the savedsettings, there is no need to configure itbefore every cycle.How to set the programme selection modeThe appliance is
Whether you use a standard detergent ormulti-tabs (with or without salt), set theproper water hardness level to keep thesalt refill notification activ
Acoustic signalsAcoustic signals sound when a malfunctionof the appliance occurs. It is not possible todeactivate these acoustic signals.There is also
3. Press on/off to confirm the setting.Before first use1. Make sure that the current level of thewater softener agrees with thehardness of the water s
Caution! Water and salt maycome out of the salt containerwhen you fill it. After you fill thesalt container, immediately starta programme to preventco
4. Add the detergent.5. Set and start the correct programme forthe type of load and the degree of soil.Using the detergent1 2213303045If the programme
When the countdown is completed, theprogramme starts.Opening the door while the applianceoperatesOpening the door while a programme isrunning stops th
containing no additional agents), rinseaid and salt separately for optimalcleaning and drying results.• At least once a month run the appliancewith th
ENGLISHPlease refer to the last page of this manual for the full list of IKEAappointed After Sales Service Provider and relative national phonenumbers
Care and cleaningWarning! Before maintenance,deactivate the appliance anddisconnect the mains plug fromthe main socket.Dirty filters and clogged spray
Cleaning the filter of the inlet hose1Close the water tap.2ADisconnect the hose.Turn the fastener Aclockwise.3Clean the filter ofthe inlet hose.4Clean
External cleaning• Clean the appliance with a moist softcloth.• Only use neutral detergents.• Do not use abrasive products, abrasivecleaning pads or s
Problem and alarm code Possible cause and solutionThe appliance does not fillwith water.The display shows or .• Make sure that the water tap is open.
Refer to "Before first use", "Daily use", or "Hints and tips"for other possible causes.Once you have checked the applian
Problem Possible cause and solutionUnusual foam during washing.• Use the detergent for dishwashers only.• There is a leak in the rinse aid dispenser.
Technical informationDimensions Width / height / depth(mm)596 / 818 - 898 / 550Electrical connection 1)Voltage (V) 220 - 240Frequency (Hz) 50Water sup
the costs to remedy the fault e.g. repairs,parts, labour and travel will be covered,provided that the appliance is accessiblefor repair without specia
For appliances which are purchased in oneEU country and taken to another EUcountry, the services will be provided in theframework of the guarantee con
emit gninepOeeF llaCrebmun enohPyrtnuoCBelgië 070 246016 Binnenlandse gesprekskosten 8 tot 20 Weekdagen eniames nE .02 à 8 xuanoitan sleppa se
ENGLISH4
117884453-A-052018© Inter IKEA Systems B.V. 201821552AA-1939327-4
ContentsSafety information 4Safety instructions 6Product description 7Control panel 8Programmes 9Options 11Settings 11Before first use 15Daily use 16H
• Children shall not carry out cleaning and user maintenance ofthe appliance without supervision.General Safety• This appliance is intended to be used
Safety instructionsInstallationWarning! Only a qualifiedperson must install thisappliance.• Remove all the packaging.• Do not install or use a damaged
• Do not remove the dishes from theappliance until the programme iscomplete. Some detergent may remainon the dishes.• The appliance can release hot st
5Rating plate6Salt container7Air vent8Rinse aid dispenser9Detergent dispenser10Cutlery basket11Lower basket12Upper basketBeam-on-FloorBeam-on-Floor is
Indicator DescriptionSalt indicator. It is always off while the programme operates.ProgrammesProgramme Degree of soilType of loadProgramme phases Opti
Kommentare zu diesen Handbüchern